Our top seller products
No results were found for the filter!
Variant available
Replacement axis for deburring cutters with ball bearing, pin
Variant selection
Spare axle for deburring cutters made of carbide, with thrust roller Ø3-5mm, with thrust pin Ø2.5mm, each with protective sleeve and 2 nuts pre-assembled.
From €26.78
*
approx. 10 weeks
1 x in stock
Deburring miller, ball bearing for miller axis / set of 5
Variant selection
Deburring miller, high-quality ball bearing Ø 3, 4 and 5 mm, spare part for deburring miller with ball bearing in a set of 5 fitting on miller axis.
€81.87
*
approx. 1-3 workdays
Subsequent delivery
Deburring miller, assembly set I, for miller axis, 5 pieces
See details
Deburring miller, assembly set I for miller axis 5 pieces, with 2 socket wrenches 3mm, 1 socket wrench 2,5mm, 2 extra flat open-end wrenches 2,5/3mm.
€68.78
*
approx. 10 weeks
1 x in stock
Deburrig tool Burr-Off®, type 1 (1.57-5.56)
Variant selection
Deburrig tool Burr-Off®, type 1 (1.57-5.56 mm) for deburring on both sides in a single operation without spindle stop.
From €105.91
*
approx. 1-3 workdays
1 x in stock
Deburrig tool Burr-Off®, type 2 (5.56-16.28)
Variant selection
Deburrig tool Burr-Off®, type 2 (5.56-16.28 mm) for deburring on both sides in a single operation without spindle stop.
From €108.29
*
approx. 1-3 workdays
3 x in stock
Deburrig tool X-Grat, type 1 (1.0-2.8)
Variant selection
Deburrig tool X-Grat type 1 (Ø 1.0-2.8 mm) for deburring on both sides in a single operation without spindle stop.
From €204.44
*
approx. 1-3 workdays
5 x in stock
Deburrig tool X-Grat, type 2 (2.8-5.56)
Variant selection
Deburrig tool X-Grat type 2 (Ø 2.8 - 5.56 mm) for deburring on both sides in a single operation without spindle stop.
From €155.77
*
approx. 1-3 workdays
4 x in stock
Deburrig tool X-Grat, type 3 (5.56-16.28)
Variant selection
Deburrig tool X-Grat, type 3 (5.56-16.28) for deburring on both sides in a single operation without spindle stop.
From €155.77
*
approx. 1-3 workdays
Variant available
Carbide end mill cutter type FZ for Makra deburring machines
Variant selection
Carbide end mill cutter FZ 810 - 860 for Makra deburring machines, with 4 - 30 cutting edges and large chip spaces suitable for almost all materials.
€67.47
*
approx. 10 weeks
Variant available
Deburring cutter with ball bearing, radius cutter made of carbide
Variant selection
Deburring cutter with ball bearing Ø 3 and Ø 4 mm, as radius cutters with universal cutting geometry and double-sided cutting edges for most materials.
From €157.44
*
Delivery time appox. 7 Workdays
Variant available
Carbide deburring miller with pin, for contours
Variant selection
Carbide deburring millers with pin for Makra deburring units, type 1 and 3, double cutting edge with starting pin Ø 2.5 mm, inexpensive and robust design.
From €93.77
*
approx. 10 weeks
1 x in stock
Carbide deburring miller with ball bearing Ø3, for contours
Variant selection
Double cutting edge carbide deburring miller with ball bearing Ø 3 mm, for contours, for Makra deburring machines, type 2 and 3, good rolling characteristics.
From €99.96
*
approx. 1-3 workdays
Variant available
Carbide deburring miller with ball bearing Ø4, for contours
Variant selection
Double cutting edge carbide deburring miller with ball bearing Ø 4 mm, for contours, for Makra deburring machines, type 2, 3, 4 and 5, good rolling characteristics.
From €104.96
*
Delivery time appox. 7 Workdays
Variant available
Carbide deburring miller with ball bearing Ø5, for contours
Variant selection
Carbide deburring miller with ball bearing Ø 5 mm, for contours for Makra deburring machines, type 4 and 5, for sensitive workpiece surfaces.
From €132.45
*
approx. 10 weeks
Variant available
Carbide deburring cutters, tip edge cutter 90°
Variant selection
Carbide deburring cutters with point in 90° version, milling angle 45°, type 8, intended for use with guide finger / ruler, with universal cutting geometry.
From €78.78
*
Delivery time appox. 7 Workdays